CISCOKILLERS

CCNA, CCNP, WLAN ANSWERS AND MUCH MOREEEEE!!
 
HomeFAQSearchRegisterMemberlistUsergroupsLog in

Share | 
 

 Module4

Go down 
AuthorMessage
Admin
Admin


Number of posts : 72
Age : 31
Localisation : Cyprus
Registration date : 2007-02-22

PostSubject: Module4   Thu Nov 29, 2007 6:55 pm

CCNA 4
Chapter 4
=========================
Use this at your own risk.
I'm not responsible for
what you do with it.
Happy cheating ^^
=========================



===========================================================================
Which of the following are true of ISDN routers configured with dialer profiles? (Choose two.)

They do not use ACL to define interesting traffic.
Their B channels can be configured with different subnets and encapsulation types. *
Their BRI interfaces can belong to multiple dialer pools. *
They use PPP only.
They can only use the CHAP authentication protocol.
===========================================================================
Which of the following describes the use of a SPID? (Choose two.)

selects the ISDN switch type
identifies the line configuration of the BRI service *
allows multiple ISDN devices to share the local loop *
designates whether a device is a TE1 or TE2
allows ISDN broadcasts
===========================================================================
What is a reason why static routes are preferred over dynamic routes for DDR to operate on an ISDN interface?

An ISDN interface will not allow dynamic routing updates that use broadcast technology.
A dynamic route will take precedence over a static route because of its lower administrative distance.
Dynamic routing can never be considered interesting traffic by default.
Dialer-list configuration does not support dynamic routing.
Dynamic routes may cause the ISDN connection to dial constantly to transmit updates. *
===========================================================================
What must be configured for an ISDN PRI connection? (Choose three.)

ISDN switch type *
Service Profile Identifier (SPID)
Dial-on-Demand Routing (DDR)
PRI group time slot*
T1/E1 controller, framing type and line coding *
===========================================================================
You have just taken delivery of a new US standard Cisco 2620 router that includes a BRI "U" interface? Which of the following describes how this router will be connected in the ISDN network?

An external terminal adapter (TA) must be attached to the router for connectivity.
An NT1 must be connected to the router for connectivity.
The router is a TE1 device and is ready to connect to the provider's network.*
The router is a TE2 device and requires both a TA and NT1 for connectivity.
===========================================================================
A network administrator is troubleshooting an ISDN connectivity problem. Users are complaining they cannot connect to the Internet. The network administrator suspects the ISDN connection attempt is timing out before a connection can be established. What command would the network administrator use to determine what the "wait for carrier" timeout value is set to?

show isdn status
show isdn active
show dialer *
show interfaces bri0/0
debug isdn q931
show ISDN interfaces
===========================================================================
Which command configures an ISDN interface to use a switch type which is different from that used on other interfaces on the router?

Router(config)#switch-type switch-type
Router(config-if)#switch-type switch-type
Router(config)#isdn switch-type switch-type
Router(config-if)#isdn switch-type switch-type *
===========================================================================
Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)

Link Access Protocol - Data
High-Level Data Link Control *
Logical Link Control
Serial Data Link Control
Point to Point protocol *
Binary Synchronous Control protocol
===========================================================================
A small company uses an ISDN WAN link to transfer e-mail to remote sites. What command would the administrator use to determine if the ISDN link is up?

show isdn status *
show isdn active
show dialer
show interface bri0/0
debug isdn active
===========================================================================
Why must routers be configured to specify the ISDN switch type?

Switches use various implementations of Q.931. *
The IOS of most routers lacks the ability to autosense the switch.
The switch must know what type of router it is communicating with.
The Layer 3 connection between the terminal equipment and the ISDN switch is not standardized.
===========================================================================
Which of the following is considered out-of-band signaling?

using a frequency outside of the rated bandwidth for transmission
transmitting data over a control channel
using a separate channel for control signals *
transmitting control signals over a data channel
===========================================================================
Which of the following is essential for all ISDN BRI interface configurations?

ISDN switch type *
line encoding technique
line framing method
local directory number
service profile identifier
===========================================================================
Which router command would be used to enter the mode for configuring a T1 PRI connection?

Router(config)# controller t1 {slot/port} *
Router(config)# interface pri t1 {slot/port}
Router(config)# interface pri {slot/port} t1
Router(config)# controller {slot/port} t1
===========================================================================
Which of the following correctly describes ISDN BRI? (Choose three.)

two 64 kbps B channels and one 16 kbps D channel *
B channel is suitable for voice data *
uses in-band signaling
uses out-of-band signaling *
offers the equivalent of a T1/E1 connection
twenty-three 64 kbps B channels and one 16 kbps D channel
===========================================================================
The network administrator of XYZ company needs to configure a new ISDN router. After entering the commands shown in the graphic, the administrator tries to access the Internet but the ISDN connection does not open. If the service provider verifies that the problem is with XYZ's configuration, what is a possible cause of the problem?

The dialer map is configured incorrectly.
The encapsulation type is configured incorrectly.
The dialer group is configured incorrectly. *
The ACL is configured incorrectly.
The isdn switch-type command needs to be configured globally.
===========================================================================
A network administrator is troubleshooting ISDN connectivity. The administrator suspects the problem lies with the authentication protocol. What command should the administrator use to view the authentication process between the router and the ISDN switch?

debug pap authentication
debug chap authentication
debug ppp authentication *
debug isdn authentication
===========================================================================
A network administrator in Europe has been asked to provide the network with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with an S/T interface. What further equipment will be provided by the ISP for the ISDN connection?

Nothing. The router is already suitable.
BRI WAN interface card to install in the router
an external NT1 to terminate the local loop *
a TA/NT1 device to install on the router
===========================================================================
Which command is used within an existing ISDN network to display current call information, including the called number?

show isdn status
show isdn active *
show interfaces bri0/0
show ip interfaces
===========================================================================
Back to top Go down
View user profile http://www.ciscokillers.tk
 
Module4
Back to top 
Page 1 of 1

Permissions in this forum:You cannot reply to topics in this forum
CISCOKILLERS :: CCNA :: CCNA 4-
Jump to: